Polaroid quilt block

I can't claim the original idea for this block, that stroke of genius goes to Corey from Little Miss Shabby, but I can share my method for making this sort of block. Once you get the hang of it, it's really quite quick & easy to put together, not to mention addicting!

First of all, if you want accurate & consistent ¼" white borders around the center picture, I recommend using paper piecing. I've put together this template if you'd like to use it. It includes four templates, I just cut them into individual pieces & work on each separately. The background isn't marked since you can make it any size you would like.

Download Template

For each Polaroid, you'll need one 2 ½" x 2 ½" picture, three 1" x 3 ½" white strips, & one 1 ½" x 3 ½" white strip, plus your background fabric.

So start out with one square from your template. If you've never paper pieced before, we're going to be doing a very easy version of it here. This block could easily be done without paper piecing, but I prefer it to get a consistent border around the picture.

The first thing you want to find is your center "picture" portion of the block. You will end up with a 2" x 2" square visible. I've cut a little template out of a scrap piece of paper. The "window" is 2" x 2" & the whole square is 2 ½" x 2 ½". This way I can see what will show & since I'm using a lot of scrap pieces, I can easily tell if they are big enough.

You can also easily play around with the placement of the part that will show before cutting anything. Then just use it as a cutting guide to cut your 2 ½" square.

Next you want to line up your square on the back side of your sewing template in area 1. So one side of your template should have your lines that you'll sew on, the other side will have your fabric right side up. I like to hold my fabric & template up to the window or a light to make sure it's centered & I have enough overlap for my seam allowances.

You can see I've cut this square bigger than 2 ½", which is fine. You just don't want to go smaller.

Now lay your first 1" white strip on the fabric side of your template in area 2. You'll be sewing on the line between 1 & 2, so again hold it up to the light to make sure you have it positioned correctly.

If your fabric had a right & wrong side, you would want it & your center block right sides together, but since this white has no right or wrong side, it's much easier.

Flip your block over to the printed side & make sure you have everything pinned in place so it doesn't shift while you are sewing it.

Make sure to turn your stitch length way down, it will better perforate your paper which will help make it easier to tear off later. If you forget (I have a time or two!), it's not the end of the world, but your paper will be harder to remove without pulling on your stitches too much. My normal stitch length is 2.5, so I go down to 1.4.

Like I said before, you'll be sewing that line between areas 1 & 2. I do like to backstitch a couple stitches at the beginning & end of each line.

Turn it over & make sure your fabrics didn't shift or fold & get caught in the stitching (happens to me all the time!). Then trim the allowance down to about ¼". It doesn't have to be exact.

Before trimming

After trimming

Next we will do the same process for the 1" white strip in area 3. Unlike most paper piecing patterns where you would sew a line between 2 & 3, they don't touch on this template, so sew on the line between 1 & 3.

Finger press both seams, then pin (from the printed side) in place to make sure they don't shift while you sew on piece 4.

Piece 4 is the last 1" strip, sewn along the top where 4 meets 2, 1, & 3.

Once again, finger press 2 & 3, then pin in place where they meet piece 5 (1 ½" white strip).

This time you'll be sewing along the bottom, where 5 meets 2, 1, & 3.

Make sure you're still trimming your seam allowances.

Finger press pieces 4 & 5. Sorry this is difficult to see, white fabric on white paper doesn't photograph well!

Now you'll start adding your background pieces. You can easily do this the same way you would do a log cabin, or any border of your choice, but I recommend still using the template since you want to keep that nice ¼" white border. Draw your lines directly onto the template for the background pieces.

Then number them if you need. I originally numbered these backwards (oops!), so ignore those crossed out numbers.

Here's a better (and easier) arrangement that works the top & bottom first, then left & right.

Sew along each line to add your background pieces, finger pressing & pinning overlapping seams as you go. If you don't finger press and/or pin your pieces as you go, they can easily get tucked in a bit & mess up your white border.

Here it is with the full border. I didn't bother trimming it, since I would trim it after adding it to the other blocks. I also didn't worry about making sure my border pieces are the same size since I want my blocks to have varied borders, but you could make them all the same size if you prefer.

If you look close, you can see on the lower left of the Polaroid where my grey got tucked in just a bit because I didn't pin it in place, so my white isn't a perfectly straight line. This time wasn't terrible, but do be careful!

Another thing to watch out for is where you sew on the lines. Try to be consistent, whether you sew down the middle of the line, or on one side or the other doesn't really matter as long as you're consistent. Here you can see I veered from one side clear to the other between areas 2 & 8.

On some paper piecing projects this won't make much of a difference, but with only ¼" of the white showing, it's pretty obvious. See how it flares out at the bottom here?

In the grand scheme of things, it shouldn't be too obvious mixed in on an entire quilt, but it's definitely something to look out for!

Once you've got multiple photo blocks put together, it's time to sew them together into bigger blocks.

Have fun with the arrangement of your pictures. You could group similar ones together like I did here, or go totally random & scrappy. Maybe you could use the pictures to tell a story. It's also a fun alternative way of making an I-spy quilt.

I've created a Flickr group for any projects you've made from my tutorials, so I'd love to see the blocks you make!

Until next time...

Tutorial: Inserting Zippers

Hopefully you saw this back in August as part of Sara's Sewing Back-to-School series, but just in case you missed it I wanted to share again!

************************************************************************

Have you ever wanted to put a zipper in the top of a bag/clutch/pouch but couldn't get everything to look all nice & pretty, especially at the seams?

Here's my (more or less) fool-proof method for adding zippers. This is not some new or ground-breaking method. In fact, there are probably other tutorials out there that use a similar method, but this is what works best for me.

First & foremost, you need to decide what you're going to make (I'm going to refer to a "pouch" to keep things simple). This method can be adapted to pretty much any pattern, or if you just want to wing it for a simple pouch. Any time I'm working on a bag pattern that requires putting in a zipper (except in the lining, for that method, this is my go-to tutorial), I skip all instructions for the zipper, do it my own way, then go back to the pattern to finish up whatever I'm making. I have yet to find a pattern where I couldn't use this method.

When you've gotten to the point where you're ready to put in a zipper (you've cut out all your pieces & applied any interfacing necessary), measure the top of your pouch, and get a zipper that is at least the same length. Zippers are sold in measurements based on the actual zip length, not the overall length (includes the amount past the zip stop). So if the pouch you are making is 12" wide at the top, you'll want to get at least a 12" zipper, which will technically be longer than your pouch. Remember, if you're using a plastic zipper, you can cut it to any length you like, so longer zippers are perfectly okay to use.

Here are the pieces I'll be using for my pouch. Each is about 13" square.

The zipper I chose is a 22" zipper, so I'll be cutting it to length a little later.

First we're going to make our zip ends. These are the little bits of fabric that will cover the ends of your zipper, act as a zipper stop, and keep your seam looking nice. It's the light-colored piece at the end of my zipper here:

Decide what fabric you want to use for your zip ends. You can choose something that matches your exterior, the zipper, the lining, or go crazy with a pop of color. In this case, I'm using the same muslin that I used for my lining. Unless you're making a tiny pouch with a very small opening, cut a piece of your fabric at least double the width of your zipper (I usually eyeball a piece around 5" long) & 2.5" wide.

(If you are making something with a very short zipper, you'll probably want shorter zip ends so you have the longest usable zipper as possible. I've gone as small as about 1" wide to start, but the smaller it is, the harder it is to work with, and doesn't look as nice on longer zippers.)

The length doesn't matter too much, as long as you have enough to cover both ends of your zipper.

With a hot & steamy iron (I use the highest settings for whatever type of fabric I'm using), press the piece in half lengthwise with the wrong sides together. Once it cools, fold one side in to the middle crease & press again. Again, once it cools, fold the other side in to the middle & press. We're basically making double-fold bias tape here (which you could use instead of making your own).

The left side has been pressed in to the middle.

Sorry, I should have used fabric that had definite "right" & "wrong" sides...

You're left with a piece that has the right side showing on both sides, is approximately 5/8" wide, and is four layers thick.

Go ahead & cut this piece in half, so you have two zip ends.

Next, take your zipper, and from the end without the pull when it's closed...

...cut off the tabs, as close to the metal stop as you can. Make sure you cut across as straight & even as possible.

(If you're working on a small pouch with a short zipper, you may actually want to cut off the metal stop so you don't have to worry about hitting it with your needle when you sew on the zip end.)

Now sandwich the end inside the zip end you just pressed. Put the end you just cut flush with the center crease.

Close it up, and pin in place.

I sew as close to the edge of the zip end (along the zipper) as I can & still make sure I'm catching both sides - about 1/16".

Make sure you backstitch at each end of the zipper. Your zip end is probably wider than your zipper at this point, you don't need to sew all the way to the end of the fabric, I start & stop just off the zipper, making sure to backstitch on the actual zipper.

Now, measure the top of your pouch again (overall length of the pattern piece, not what you think the finished size will be). You're going to want to make a mark on your zipper just a smidge (technical term, I know...) over an inch shorter than the width of your pouch. I like to sew with a 3/8" seam, so you can adjust accordingly depending on how wide of a seam you like to sew. I've found that cutting the zipper about 1 1/8"-1 1/4" shorter than the pouch works best for me.

Remember, my pieces are 13" square, so I marked my zipper at 12", and I'll cut just short of the line.

This is important!!! Do not, I repeat DO NOT, cut your zipper at the line if it looks like the picture above. Don't even think about it. I know it would be so much easier to cut it when it's closed up like that, but you'll be leaving your pull on the wrong side.

Move your zipper pull past your line (towards the zip end you already sewed on - mine is off to the right), so it looks like this:

Before you cut it, sew it together below your line. It doesn't have to be pretty, you just want the two halves held together when you sew on your zip end. Trust me, it'll make things much easier in a minute. I just hand sew it with a few stitches.

(Sorry, I turned my zipper around between pictures. My finished end is now on the left.)

Once you've sewn the ends together, double check that your zipper pull is in the correct part of the zipper, then go ahead & cut the zipper. If you marked your zipper an inch shorter than your opening (like I did), then cut it a little smaller. If you marked it right at 1 1/8"-1 1/4" shorter than the pouch, then go ahead & cut right on your line. Again, try to cut it as straight & even as possible.

Now, just like the other end, sandwich it in the middle of your remaining piece of zip end, push up flush with the crease, pin, and sew in place.

Trim your zip ends so they're even with the width of the zipper. Your zipper (including zip ends) should now be finished on both ends & approximately an inch shorter than the top of your pouch.

Take the first exterior piece for your pouch, it doesn't matter which one, and lay it down rightside up. Center your zipper wrong side up along the top edge of your exterior piece. You want the "working" side of the zipper to be facing the right side of your exterior. Basically, you're placing the fabric & zipper right sides together. It doesn't matter which end the zipper pull is on, unless you have a preference (I always sew my first piece with the zip pull on the left). Make sure the zipper is centered - you can either measure on each side of the zipper (my method of choice), or fold the zipper & fabric in half then match up the center points. Open your zipper a couple inches, then pin in place so that the edge of the zipper is flush with the top edge of your fabric.

(Note: You can skip this next step, basting in the zipper, if you'd like. Personally, I'm not typically a fan of basting, but I always baste my zipper to the exterior. If you want to skip the basting, you'll sandwich your zipper between your exterior and lining pieces in this order - exterior right side up, zipper right side down, and lining right side down. Like I said, I always baste (even when I made 22 zippered pouches at once!!), but it's totally up to you. If this is your first time sewing a zipper, I really can't recommend basting enough.)

Baste the zipper in place, about 1/8" from the edge (not right along the zipper teeth). Be sure to sew over the zip ends as well, but don't go past them. When it comes to sewing zippers, I always,alwayspull out my pins as I get to them. They always seem to pull the zipper out of place just a bit & can cause problems if you leave them in. So, even if you normally sew over your pins (guilty as charged!), do yourself a favor & pull them when sewing anything with a zipper.

When you get close to the zipper pull, stop with your needle in the down position.

Take your foot off & completely away from the peddle. Some people will say to go ahead & shut off your machine too, but I can't since my needle moves every time I turn the machine on. Basically, just don't sew through your finger on this next part. :)

Lift your presser foot & move the zipper pull past the foot so it's out of your way to finish sewing. This can take some crazy maneuvering sometimes, and more than once I've had to remove the foot to get the zipper by. Personally, I prefer to sew as much of the zipper as possible with the zipper closed. So you may move it more towards the end, depending on which end of the zipper you're coming from.

Finish basting on your zipper, making sure to backstitch at the end of the zip end.

Sorry my stitches are light & hard to see here.

Once again, open your zipper a few inches.

Place your first lining piece wrong side up, so the top is flush with the zipper & exterior piece. Pin in place.

The double pins on the ends mark the ends of the zipper & the double pins in the middle mark the zipper pull. If you can tell where the zipper ends (you don't want to sew past the zipper), you don't need to mark those, but I recommend at the very least marking your zipper pull so you don't forget & get too close.

Switch to your zipper foot & sew along the edge of the zipper. We are sewing on the right side of the zipper, so you should attach on the left side of the zipper foot. The ledge of the zipper foot should sit on top of the zipper, and on mine, I know I can line up the right side of the little sled part (again with the technical terms...) with the edge of my fabric & have it sew nice & close to the zipper, but not too close.

Start & stop at the ends of the zipper (including zip ends), but do not sew off the ends where you just have the lining & exterior together. Be sure to backstitch at each end. Stop when you get within about an inch of your zipper pull, leave your needle down, lift the presser foot, and move the zipper past the foot. Don't forget to pull your pins as you go instead of sewing over them!

When you get to the end & open it up, you should have this:

Both lining & exterior are right side up & the working side of the zipper is on the exterior side.

Flip the lining all the way over so the lining & exterior are now wrong sides together. Work the seam along the zipper so it's nice & flat on both sides, then pin in place.

Topstitch along the edge of the zipper. You can either use your zipper foot or switch back to your regular foot (my choice). You want to stitch about 1/8" away from the edge of the fabric.

OR

This will help keep your exterior, and especially your lining from getting stuck in the zipper.

Now, we're going to repeat the whole process with the other exterior & lining pieces.

Place your remaining exterior piece down right side up, and put your zipper (now with an exterior & lining attached) on wrong side up on top. Your two exterior pieces will be right sides together, with the right side of a lining on top.

Line up the zipper flush with the top edge of your exterior fabric & pin in place.

Baste your zipper in place the same as before, about 1/8" away from the edge.

Lay your remaining lining piece on top, wrong side up. Make sure to mark your zipper pull.

Your two lining pieces should be right sides together.

Once again, switch to your zipper foot, and sew, making sure to stop & move your zipper pull when you get to it, and start & stop at the end of the zipper, not the end of the fabric.

If you open it all up & lay it flat, you should have both right sides of the exterior along with the working side of the zipper.

And if you flip the whole thing over, you should have both right sides of the lining along with the back side of the zipper.

Now, on the pieces you just attached to the zipper, once again work the seam so it lays flat & pin so you can topstitch along the edge of the zipper, the same as you did for the first side.

At this point, you may now return to your regularly scheduled pattern, if you were following one. If not, read on to finish up your pouch.

If you want to add any kind of loop for a handle, now is the time to do it. Make your loop (I use the same method as I did for the zip ends - basically making double-fold bias tape, but much smaller. I think this piece was 1" before folding & pressing.), then pin & baste it in place.

IMPORTANT!!! Right this very second, open your zipper. Do not forget or you will not stop cursing yourself later. Trust me, it's possible to open a zipper from the wrong side, but it is noteasy. Not at all. And do yourself a favor, open it all the way. Again, trust me, you'll thank yourself later.

Fold the pieces back so your exteriors are right sides together & linings are right sides together, with the zipper in the middle. Pin in place.

I always use double pins to mark where I need to leave my opening for turning. If I don't, I'll forget & sew all the way around.

I have found the absolute, best method for turning is this one from Michelle at Keyka Lou. If you aren't using this method, do me a favor & at least try it a time or two. I promise you'll never want to do it another way, and if you do, I want to know what your better method is. You can thank me later. ;)

When you're sewing it all together, do not sew over your zip ends when you get to that point, just sew in the space next to them. You'll probably have to decrease your seam allowance to squeeze by, and sometimes I even switch to my zipper foot so I can get as close as possible to the zip ends without actually sewing them into the seam.

If you're making a basic flat pouch, just sew all the way around, turn through your opening, sew the opening closed, and carefully push the seams into place at the ends of your zipper. Remember, your seam allowance here is probably smaller than everywhere else, so be gentle, but you can get them pushed out nicely.

If you want to make a pouch with a flat bottom, sew around only your exterior, start & stopping about an inch on the lining side of the zipper. If you make your gussets in your exterior beforesewing the lining, you've got the entire zipper to reach through, which is much easier than trying to reach through the opening you leave in the lining. Once your exterior gussets are made, sew around the lining piece, then use your turning opening to make your gussets.

When you're all done, you should have a nice little pouch with a pretty zipper! It still takes some practice, but after you do it a few times, you'll have the process down so you barely have to think about it.

Good luck! If you have any questions, let me know & I'll try to clear anything up that might not quite make sense.

Until next time...